Alloy | Description | Composition | Applications |
---|---|---|---|
6005A | 6005A is the weakest of the three structural alloys (6005A, 6061 and 6082). As with all structural alloys it is difficult to produce thin walled or complicated extrusions in 6005A however, of the structural alloys, it has the best extrusion characteristics and mill surface finish. 6005A is a heat treatable alloy with excellent corrosion resistance. It also has good weldability. |
Mg : 0.40 - 0.70 Mn : ≤0.50 Fe : ≤0.35 Si : 0.50-0.90 Cu : ≤0.30 Zn : ≤0.20 Cr : ≤0.30 Mn+Cr : 0.12-0.50 Ti : ≤0.10 Other Elem : ≤0.05 Total Other : ≤0.15 Al : Rem. |
|
6060 | 6060 alloy is one of the most common alloys of the 6000 series. It is a heat treatable alloy with very good corrosion resistance and weldability. It is commonly used in window and door frames in residential and commercial applications. It is an ideal alloy for very complex cross sections and has a very good anodising response. |
Mg : 0.30 - 0.60 Mn : ≤0.10 Fe : 0.10-0.30 Si : 0.30 - 0.60 Cu : ≤0.10 Zn : ≤0.15 Cr : ≤0.05 Ti : ≤0.10 Other Elem : ≤0.05 Total Other : ≤0.15 Al : Rem. |
|
6061 | 6061 is a heat treatable alloy with mechanical properties slightly lower than 6082. It has good corrosion resistance but like 6082 its extruded surface finish is not as good as 6060. |
Mg : 0.80 -1.20 Mn : ≤0.15 Fe : ≤0.70 Si : 0.40 - 0.80 Cu : 0.15-0.40 Zn : ≤0.25 Cr : 0.04 - 0.35 Ti : ≤0.10 Other Elem : ≤0.05 Total Other : ≤0.15 Al : Rem. |
|
6082 | 6082 has excellent corrosion resistance and the highest strength of the 6000 series structural alloys. As with all structural alloys the extruded surface finish is not as good as alloys such as 6060 or 6063. The higher strength of 6082 has seen it replace 6061 in many applications. 6082 has good weldability and when DNV(Det Norske Veritas) certifi ed it is commonly used in marine applications. |
Mg : 0.60 -1.20 Mn : 0.40 -1.00 Fe : ≤0.50 Si : 0.70-1.30 Cu : ≤0.10 Zn : ≤0.20 Cr : ≤0.25 Ti : ≤0.10 Other Elem : ≤0.05 Total Other : ≤0.15 Al : Rem. |
|
6101 | 6101 is a heat treatable alloy specifically designed for electrical conductors with an electrical conductivity slightly higher than 6060 or 6063. |
Mg : 0.35-0.80 Mn : ≤0.03 Fe : ≤0.50 Si : 0.30 - 0.70 Cu : ≤0.10 Zn : ≤0.10 Cr : ≤0.03 Bi : ≤0.06 Other Elem : ≤0.03 Total Other : ≤0.10 Al : Rem. |
|
6106 | 6106 is a heat treatable alloy with mechanical properties between 6060 and 6061/6082. It has excellent corrosion resistance and its good extrudability enables more complex shapes to be extruded than can be produced with 6061 or 6082. |
Mg : 0.40 - 0.80 Mn : 0.05- 0.20 Fe : ≤0.35 Si : 0.30 - 0.60 Cu : ≤0.25 Zn : ≤0.15 Cr : ≤0.20 Ti : ≤0.10 Other Elem : ≤0.05 Total Other : ≤0.15 Al : Rem. |
|
6351 | 6351 is a heat treatable alloy very similar to 6082 with similar characteristics including corrosion resistance and strength. Many European specifications now call up 6082 in lieu of 6351. |
Mg : 0.40 - 0.80 Mn : 0.40 - 0.80 Fe : ≤0.50 Si : 0.70 -1.30 Cu : ≤0.10 Zn : ≤0.20 Ti : ≤0.20 Other Elem : ≤0.05 Total Other : ≤0.15 Al : Rem. |
|
1000 | 1000 series alloy, generally called commercial pure aluminium, the Al content of this series is above 99.0%. Feature: high conductivity, good corrosion resistant performance, high latent heat of melting, high-reflectance, well welding property, low strength, and not suitable for heat treatments. 1100,1050,1060,1070,1070ec. | Available on request |
|